General value of a standard 25 micron Polyester Glitter.

Item
 
asf
Value
Unit
Test Condition
Test Method
 Tensile Strength
MD
23
Kg/mm2
25 C
ASTM-D882A
TD
24
Kg/mm2
 Elongation at Bank
MD
120
%
TD
110
%
 Young's Modulus
MD
450
Kg/mm2
TD
500
Kg/mm2
 Impact Strength
-
35
Kg/cm2
25 C
ASTM-D1709
 Tear Strength
MD
14.6
g
Atmosphere
ASTM-D1922
TD
15
g
Atmosphere
ASTM-D1922
 Bursting Strength
5.5
Kg/cm2
25 C
ASTM-D774
 Folding Endurance
1.5 x10
Cycles
MIT Method
ASTM-D2176
Item
Value
Unit
Test Condition
Test Method
 Density
1.4
g/m2
25 C
ASTM-D1505
 Water Absorption
0.45
%
25 C ,24hr
ASTM-D570
 Water Vapor  Permeability
23
g/m2/24hr
40 C,90% RH
ASTM-E96
 Oxygen Permeability
45
cc/m2/24hr/atm
24 C, 1atm
ASTM-D1434
 
Item
Value
Unit
Test Condition
Test Method
 Melting Point
260
-
-
TSI Method
 Service Temperature
-70 ~ 150
-
-
-
 Heat Shrinkage
MD
1.5
150 C/30min
150 C/30min
ASTM - D2305
TD
0.5
 Thermal Expansion  Coefficient
3x10
10~50 C
10~50 C
ASTM - D696
 Thermal Expansion  Coefficient
3x10
-
-
-
 Specific Heat
0.32
25 C
25 C
-
Item
Value
Unit
Test Condition
Test Method
 Refractive
1.65
nD
25 C
ASTM - D542
 Total Luminous  Transmission
5
%
25 C
ASTM - D1003
 Index Haze
3
%
 
 
 
  Melting Point : 255 ~ 265 C (491 ~ 477 F)
  Boiling Point : Not applicable
  Colour : Clear, Hazy, White ,Yellowish
  Heat of Combustion : 23.5 MJ/Kg
  Vapor Pressure (mmHg at 20 C) : Negligible
  Vapor Density ( air = 1) : Not applicable
  Solubility Gravity : Insoluble
  pH : Not applicable
  Specific Gravity : 1.40 g/cm
  Appearance : Film
  Odour : Odourless
  Colour : Clear, Hazy, White ,Yellowish
 
 
  Flash Point : 346 ~ 399 C (655 ~ 750F)
  Autoignition Temp : No data
  Flammable Limits (STP) : Not applicable
  Extinguishing Media: Water Spray ,Carbon Dioxide ,Dry Chemical,Halogenated Agents.
 
  Special Fire Fighting Protective Equipment:Self-contained breathing apparatus with
  fullpiece and protective clothing.
 
 
  Unusual Fire and Explosion Hazards: Film remaining in contact with flame will ignite and
  continue to burn slowly, dropping flaming liquid which can spread the fire. If the flame
  source is stationary, the fire will shrink away and self-extinguish.
 
 
Stability: Stale under normal considers.
Incompatibility (Materials to Avoid): Not applicable.
Hazardous Decomposition Products : Combustion products: Carbon Dioxide, Carbon Monoxide ,Terephthalic Acid, Aldehdes
Hazardous Polymerization: Will not occur
Health Hazard Assessment
 
 

 

  The health Hazard assessment is based on an evaluation of the chemical composition together with information from a search of the scientific literature and other commercial sources
 
 

 

  Not suitable for human consumption.
 
 

 

  No irritation is likely to develop following contact with human eyes.
 
 

 

  No irritation is likely to develop following contact with human skin.
 
 

 

  This product will probably not be absorbed through human skin.
 
 

 

  No toxic effects are known to be associated with inhalation of dust from this material.
 
 

 

  Wash material off the skin with plenty of soap and water. If redness, itching or a burning sensation develops, get medical attention.
 
 

 

  Immediately flush with plenty of water .After initial flushing ,continue flashing for at least 15 minutes . If redness, itching or a burning sensation develops, have eye examined and treated by medical personnel.
 
 

 

  Give one or two glasses of water to drink. If gastrointestinal symptoms develop, consult medical personnel.
 
 

 

  Remove victim to fresh air .If cough or other respiratory Systems develop, consult medical personnel.
 
 

 

  Steps to be taken in case material is released or spilled: Collect for reuse or disposal.
  Disposal Method: Observe all federal, state and local laws regarding health and pollution.
 
 

 

  1) Respiratory Protection ( Specify Type): None should be needed.
  2) Ventilation:
 
  Local Exhaust : Not applicable

Other : Not applicable

  3) Protective Clothing: None should be needed
  4) Eye Protection: Not applicable
  5) Other Protective Equipment: one should be needed

NOTE: This MSDS is true but only for information, which doesn't means all coverage related to the product safety matters. Glitron Products doesn't take the responsibility of all damages due to these products.